ماژول راه انداز موتور L298

ماژول راه انداز L298 جهت استفاده بر روی انواع ربات و دستگاه های صنعتی



  • تضمین بهترین قیمت بازار
  • پشتیبانی عالی ۲۴ ساعته، ۷ روز هفته
  • مهلت تست محصولات
  • کالا های با کیفیت
  • تحویل سریع در کمترین زمان ممکن

ناموجود

معرفی ماژول راه انداز L298 ،جهت راه اندازی موتورهای DC ، با استفاده از میکروکنترلر می توانید سرعت و جهت حرکت موتور را کنترل کنید. این درایور توانایی کنترل همزمان 2 موتور DC را دارد. از این ماژول می توان جهت راه اندازی دو موتور DC یا یک موتور پله ای Stepper Motor استفاده کرد.

کاربردها

  • رباتیک
  • کنترل موتورهای DC
  • کنترل و راه اندازی موتور پله ای

مشخصات

  • حداکثر ولتاژ قابل اعمال به موتور: 50 ولت
  • حداکثر جریان مجاز خروجی ها: 2 آمپر برای هر کانال
  • دارای دو کانال خروجی برای دو موتور DC

Introduction

L298N is a high voltage, high current motor drive chip produced by ST. The chip is available in a 15-pin package. The main features are: high working voltage, the highest working voltage can reach 46V; the output current is large, the instantaneous peak current can reach 3A, the continuous working current is 2A; the rated power is 25W. High-voltage, high-current, full-bridge driver with two H-bridges that can be used to drive inductive loads such as DC motors and stepper motors, relay coils; control with standard logic level signals; with two enable control terminals, Allow or disable device operation without input signal. There is a logic power input to make the internal logic circuit work at low voltage; external sense resistor can be connected to feedback to the control circuit. Using the L298N chip to drive the motor, the chip can drive a two-phase stepper motor or a four-phase stepper motor, or two DC motors. This module integrates a built-in 5V power supply. When your driving voltage is 7V-35V, you can enable the onboard 5V logic power supply. When using the onboard 5V power supply, the +5V power supply in the interface should not input voltage, but can draw 5V voltage for external use. When ENA is enabled IN1 IN2 Control OUT1 OUT2. When ENB is enabled IN3 IN4 Control OUT3 OUT4

Specification
Double H bridge drive
Chip: L298N (ST NEW)
Logical voltage: 5V
Drive voltage: 5V-35V
Logical current: 0mA-36mA
Drive current: 2A(MAX single bridge)
Max power: 25W
Size:43 x 43 x 26mm
Net weight: 26g
Package weight:36g

نقد و بررسی‌ها

هنوز بررسی‌ای ثبت نشده است.

اولین کسی باشید که دیدگاهی می نویسد “ماژول راه انداز موتور L298”

نشانی ایمیل شما منتشر نخواهد شد. بخش‌های موردنیاز علامت‌گذاری شده‌اند *

16 − سیزده =

سبد خرید

هیچ محصولی در سبد خرید نیست.

ورود به سایت